全国咨询热线
现在一些大型的食品加工设备开始走进人们的视线中，但是人们对于这些大型设备的认识还不过深刻，今天就在这里简单的给大家介绍一下蔬果切丁机应该如何使用及其保养的注意事项。
Now some large-scale food processing equipment has come into people's sight, but people's understanding of these large-scale equipment is still profound. Today, I will briefly introduce how to use and maintain the fruit and vegetable Dicer.
切丁机 指适用于脱水蔬菜、速冻蔬菜加工厂及食品酱菜行业加工各种根、茎类蔬菜成正方体及长方体形状的机器总称。那么切丁机在使用前要做哪些准备工作呢？
Dicer refers to the general name of machine which is suitable for processing various root and stem vegetables into cube and cuboid shapes in dehydrated vegetables, frozen vegetable processing plants and food and pickle industries. So what preparation should be done before using the Dicer?
1、仔细检查切丁机是否存在缺、损、松问题，确保机器处于完好状态。
1. Carefully check whether there are defects, damages and looseness in the cutting machine to ensure that the machine is in good condition.
2、检查壳体内是否有异物存在，将壳体内异物掉，否则容易引起刀片的损坏。
2. Check whether there is any foreign matter in the shell, and remove the foreign matter in the shell, otherwise it is easy to cause damage to the blade.
3、清理操作场地，检查电源电压是否与本机使用电压相符，接志处是否可靠连接地线.合上开关，按下＂开＂按钮，检查转向是否正确（面对推料拨盘，推料拨盘逆时针方向旋转为正确），否则，切断电源调整接线。
3. Clean the operation site, check whether the power supply voltage is consistent with the use voltage of the machine, and whether the ground wire is reliably connected at the grounding mark. Close the switch, press the "on" button, and check whether the steering direction is correct (when facing the pusher dial, the pusher dial rotates counterclockwise to be correct). If not, cut off the power supply and adjust the wiring.
4、接通水源，以备使用。
4. Connect the water source for use.
切丁机的保养问题：
Maintenance problems of Dicer:
1、每次使用后必须对机器进行清洗，尤其是物料通过的地方和通道，保持切丁机的干净。
1. After each use, the machine must be cleaned, especially the place and passage where the materials pass, to keep the cutter clean.
2、每次使用后，应细心检查切丁机所有的切割刀具是否有损坏或磨钝，检查梳子刀口是否正常或损坏.每周拆卸一次圆盘切丝组合刀具和横切断组合刀具（拆卸时要小心谨慎，使用专用工具，以免伤手），并进行适当的清洗.当切丁机重新装配时，切丁机须用无味的食物油进行保养，安装前必须在切丝轴和切断轴上涂抹上食物油，以保证其拆卸方便。
2. After each use, carefully check whether all cutting tools of the Dicer are damaged or blunt, and check whether the comb blade is normal or damaged. Dismantle the disc cutting combination tool and the transverse cutting combination tool once a week (be careful when disassembling, use special tools to avoid hurting hands), and clean them properly. When the Dicer is reassembled, the Dicer must be non-toxic Before installation, food oil must be applied on the cutting shaft and cutting shaft to ensure convenient disassembly.
3、每两周给齿轮与链条注油一次。
3. Oil the gear and chain every two weeks.
4、切丁机各种刀具的修磨。
4. Grinding of all kinds of cutting tools of the cutting machine.
以上果蔬 切丁机 为您介绍的详细内容，更多内容请咨询我们 公司官网http://www.chinafoodjx.com
Please refer to our website for more details of the above fruit and vegetable Dicer http://www.chinafoodjx.com
