全国咨询热线
将刀具从切片机上拆卸下来，并将其放在一粗面实验台上，这样在砥磨时就不容易活动;然后在磨石面滴入少量的稀润滑油或液体石蜡并均匀抹开，以便增加磨擦密度。
Disassemble the cutter from the slicer and put it on a rough surface, so that it is not easy to move when grinding. Then a small amount of dilute lubricating oil or liquid paraffin is dripped in the center of the grindstone and evenly spread in order to increase the friction density.
切片机经过一段时间的使用之后，它的刀片有可能会出现不同程度的磨损或是钝化，为了不影响切片效果，必须要对切片机的刀片进行砥磨，使其恢复良好的工作状态，从而进一步提高切片效率和效果。
After a period of use, the blade of the slicer may be worn or passivated to varying degrees. In order not to affect the slicing effect, the blade of the slicer must be grind to restore the good working condition, thus further improving the efficiency and effect of the slicing.
接着将刀柄和刀夹装在切片机的刀片上使刀刃向前，平放在磨石面上，刀跟大致位于磨石的。砥磨时，手指应保持正确位置以使用力均匀易于滑动，将切片刀从磨石的右下角刀端向磨石的左上角向前斜推进刀跟，将刀刃从上面翻转。
Then the knife handle and knife clip are mounted on the blade of the slicer, so that the knife edge is moved forward and laid on the grindstone surface, and the knife is roughly located in the center of the grindstone. When grinding, the finger should be kept in the right position to use the force evenly and easily. The slicer is pushed forward from the lower right corner of the millstone to the upper left corner of the grindstone to the heel, and the blade is turned over.
在翻转切片机的刀片时，刀夹不能离石，将刀横向移动使刀跟的刀刃处于磨石前端的中心，再斜着拉回。此时再将刀刃从上面翻且将刀横向移动使切片刀在磨面上处于原来的位置。像这样反复进行，但要注意避免倾斜，并要防止油腻的手指从刀面滑开。
When turning the blade of the slicing machine, the cutter can not leave the stone, move the knife horizontally, cause the blade of the knife to be at the center of the front end of the grinder, and pull back again. At this point, the blade is turned from above and the knife moves laterally so that the slicing knife is in the original position on the grinding surface. Repeat like this, but avoid sloping and prevent oily fingers from slipping away.
如果切片机的刀片损伤较大的话，必须用粗细两种磨石，在粗磨石上磨掉大缺口，再在细磨石上磨锋利。为了提有效率，可以采用向前推进式磨刀法，一般只需要20分钟左右就可以将其磨锋利了。
If the blade of the slicer is damaged, it is necessary to use two kinds of grindstones, grinding large gaps on rough grindstones, and sharpening them on fine grindstones. In order to improve efficiency, the forward advancing sharpening method can be used. It usually takes about 20 minutes to sharpen it.
往切片机附带的滚筒内注入一定量的水，用水将其中的废屑排出;然后用软布或者软刷子沾有兑着洗涤剂的水擦拭，然后用清水冲洗干净，以便清洗剂残留其中。
A certain amount of water is injected into the cylinder attached to the slicer, and the waste chips are discharged with water; then the water is wiped with a soft cloth or a soft brush with the washing agent. Then rinse with clean water so that the cleaning agent remains.
以上便是切丝切片机今天的分享，您还满意吗，欢迎关注我们的网站:http://www.chinafoodjx.com并且关注我们的产品，我们将为您提供优良的产品，衷心的愿与您建立合作关系。
The above is the cutting silk cutting machine today to share, are you satisfied, welcome to our website: http://www.chinafoodjx.com and pay attention to our products, we will provide you with excellent products, sincerely wish to establish a cooperative relationship with you.
